Product Overview and Selection Scope
NM5R5L334S-P120614 is a 5.5 V, 0.33 F combined supercapacitor with wire leads. Its compact package is intended for low-power state retention, short data-save intervals and controlled shutdown functions where PCB area is limited.
This device is polarized and its terminal voltage falls during discharge. Verify the ESR step, capacitance tolerance, load profile, leakage, charging current and minimum system voltage in the complete circuit.
Part-Number Construction
The designation is decoded below using the naming table in the supplied specification.
| Segment | Meaning | Value for this product | Engineering note |
|---|---|---|---|
| NM | Series | Combined supercapacitor module | Distinguishes the module construction in the source naming system. |
| 5R5 | Rated-voltage code | 5.5 V | Do not exceed the rated voltage. |
| L | Terminal format | Wire lead | Confirm footprint and polarity before PCB release. |
| 334 | Capacitance code | 0.33 F | Nominal capacitance before tolerance and ageing margins. |
| S | Capacitance tolerance | −20% to +50% | Use 0.264 F as the initial minimum for conservative calculations. |
| P | Function code | Power type | Source naming classification; not a system-level power rating. |
| 12 / 06 / 14 | Body size codes | 12 / 6 / 14 mm | Nominal W / D / L dimensions. |
Electrical Characteristics
Values are transcribed from the supplied specification. Keep the stated units and test conditions attached to each parameter during comparison and design review.
| Parameter | Condition | Specified value | Unit |
|---|---|---|---|
| Rated voltage | UR | 5.5 | V |
| Nominal capacitance | C | 0.33 | F |
| Capacitance tolerance | Initial value | −20 to +50 | % |
| Operating temperature | Ambient range | −40 to +70 | °C |
| Maximum equivalent series resistance | RAC, 1 kHz | 700 | mΩ |
| Maximum leakage current | After 72 h at rated voltage | 0.002 | mA |
| Maximum operating current | Temperature rise ΔT = 15 °C | 0.16 | A |
| Maximum peak current | Source-specified peak value | 0.37 | A |
| Maximum stored energy | 0.5CUR2 / 3600 | 0.0009 | Wh |
| Energy density | Source value | 0.33 | Wh/kg |
| Power density | Source value | 432.1 | W/kg |
The supplied PDF lists maximum stored energy as 0.0009 Wh. The ideal value calculated from 0.5CU² / 3600 using 0.33 F and 5.5 V is approximately 0.00139 Wh. This page preserves the source value; confirm the intended value with NYFEA before energy-budget approval.
Mechanical Dimensions and Polarity
The package is polarized. The marked negative terminal must match the PCB polarity, and the leads must not be used to absorb mechanical stress.
| Dimension | Nominal | Tolerance | Design use |
|---|---|---|---|
| W | 12.0 mm | ±1.0 mm | Body width |
| D | 6.0 mm | ±1.0 mm | Body depth |
| L | 14.0 mm | ±1.5 mm | Body length |
| φd | 0.6 mm | ±0.05 mm | Lead diameter |
| P | 9.0 mm | ±0.5 mm | Lead pitch |
Reliability and Endurance
The specification defines post-test limits for capacitance change and internal resistance. These are qualification conditions, not continuous-use permissions at every limit.
| Test | Source condition | Capacitance change | Resistance limit |
|---|---|---|---|
| Cycle life | 500,000 constant-current cycles at 25 °C between rated voltage and half-rated voltage | ≤ 30% from initial | ≤ 4 × initial |
| Storage life | 1000 h with no load at the upper rated-temperature condition | ≤ 30% from initial | ≤ 4 × initial |
| Endurance | 1000 h at rated voltage at the upper rated-temperature condition | ≤ 30% from initial | ≤ 4 × initial |
| Life assessment | 10 years at 25 °C and rated voltage | ≤ 30% from initial | ≤ 4 × initial |
| Temperature characteristic | −40 °C, +25 °C and +70 °C | ≤ 30% from initial | ≤ 2 × initial |
| Damp-heat storage | +40 ±2 °C, 90–95% RH, 240 h | ≤ 30% from initial | ≤ 2 × initial |
Capacitance and ESR Test Methods
For capacitance measurement, charge the device to rated voltage for 30 minutes and discharge it at the prescribed constant current. ESR is measured using the specified 1 kHz AC method.
Hold-Up, Leakage and Energy Calculations
Estimate the usable interval from the allowable voltage window and load current, then subtract the immediate ESR voltage step. For leakage-current testing, fully discharge the device for 1–24 hours, apply rated voltage for 72 hours, and then measure the current.
PCB Mounting, Soldering and Handling
Assembly and environmental conditions directly affect reliability. Apply the following source-specification precautions during layout and process qualification.
If devices are connected in series, implement voltage balancing and obtain NYFEA application guidance. Also validate hole size, lead pitch, cleaning chemistry, polarity inspection and mechanical support before release.
Application Guidance and Design Limitations
The applications below are engineering use cases consistent with a compact 5.5 V, 0.33 F backup component. They are not end-product certification claims.
RTC BackupMaintain timekeeping through a brief loss of the main supply.
Memory RetentionSupport low-power state preservation and orderly data save.
Smart Meter Data SaveProvide a short window for nonvolatile recording after mains loss.
Compact Control NodesBridge short interruptions after validating the source-listed current limit.
Wireless Sensor BackupMaintain low-power state between supply events after circuit validation.The source specification does not claim automotive, medical, functional-safety, life-support or fault-tolerant qualification. Confirm all mandatory standards for the end product.
NM5R5L334S-P120614 Engineering FAQs
What are the rated voltage and nominal capacitance?
The rated voltage is 5.5 V and the nominal capacitance is 0.33 F.
What capacitance tolerance is specified?
The supplied specification states −20% to +50%, corresponding to an initial range of 0.264 F to 0.495 F before additional temperature and ageing allowances.
What is the maximum ESR?
The maximum AC equivalent series resistance is 700 mΩ using the specified 1 kHz test method.
What is the operating temperature range?
The specified operating range is −40 °C to +70 °C.
What are the package dimensions and lead pitch?
The nominal body is 12.0 × 6.0 × 14.0 mm, with a 9.0 mm nominal lead pitch and 0.6 mm nominal lead diameter.
Is the component polarized?
Yes. Match the negative marking to the PCB polarity before soldering.
Can it be used as a direct battery replacement?
No. A supercapacitor has continuous voltage decay and an ESR-related voltage step. Validate the load current, minimum system voltage, usable energy and required hold-up time.
Why should the stored-energy value be confirmed?
The source PDF states 0.0009 Wh, while the ideal formula using 0.33 F and 5.5 V gives approximately 0.00139 Wh. Confirm the controlled stored-energy value with NYFEA before production release.
Which document controls production decisions?
The supplied NM5R5L334S-P120614 PDF and the current NYFEA-controlled revision remain the design authority.
This page summarizes the supplied NM5R5L334S-P120614 product specification for component evaluation. Confirm the current revision, dimensions, polarity, stored-energy value, test conditions, assembly process and qualification requirements before production release.
